165cb93452
Analog pins was added with the wrong pin number, needs to be offset +55 to protect against using the pin as a digital
906 lines
25 KiB
C
906 lines
25 KiB
C
#ifndef PINS_H
|
|
#define PINS_H
|
|
#define ALARM_PIN -1
|
|
|
|
/****************************************************************************************
|
|
* Arduino pin assignment
|
|
*
|
|
* ATMega168
|
|
* +-\/-+
|
|
* PC6 1| |28 PC5 (AI 5 / D19)
|
|
* (D 0) PD0 2| |27 PC4 (AI 4 / D18)
|
|
* (D 1) PD1 3| |26 PC3 (AI 3 / D17)
|
|
* (D 2) PD2 4| |25 PC2 (AI 2 / D16)
|
|
* PWM+ (D 3) PD3 5| |24 PC1 (AI 1 / D15)
|
|
* (D 4) PD4 6| |23 PC0 (AI 0 / D14)
|
|
* VCC 7| |22 GND
|
|
* GND 8| |21 AREF
|
|
* PB6 9| |20 AVCC
|
|
* PB7 10| |19 PB5 (D 13)
|
|
* PWM+ (D 5) PD5 11| |18 PB4 (D 12)
|
|
* PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM
|
|
* (D 7) PD7 13| |16 PB2 (D 10) PWM
|
|
* (D 8) PB0 14| |15 PB1 (D 9) PWM
|
|
* +----+
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 0
|
|
#define KNOWN_BOARD 1
|
|
|
|
#ifndef __AVR_ATmega168__
|
|
#error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu.
|
|
#endif
|
|
|
|
#define X_STEP_PIN 2
|
|
#define X_DIR_PIN 3
|
|
#define X_ENABLE_PIN -1
|
|
#define X_MIN_PIN 4
|
|
#define X_MAX_PIN 9
|
|
|
|
#define Y_STEP_PIN 10
|
|
#define Y_DIR_PIN 7
|
|
#define Y_ENABLE_PIN -1
|
|
#define Y_MIN_PIN 8
|
|
#define Y_MAX_PIN 13
|
|
|
|
#define Z_STEP_PIN 19
|
|
#define Z_DIR_PIN 18
|
|
#define Z_ENABLE_PIN 5
|
|
#define Z_MIN_PIN 17
|
|
#define Z_MAX_PIN 16
|
|
|
|
#define E_STEP_PIN 11
|
|
#define E_DIR_PIN 12
|
|
#define E_ENABLE_PIN -1
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS -1
|
|
#define LED_PIN -1
|
|
#define FAN_PIN -1
|
|
#define PS_ON_PIN 15
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#define HEATER_0_PIN 6
|
|
#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/****************************************************************************************
|
|
* Sanguino/RepRap Motherboard with direct-drive extruders
|
|
*
|
|
* ATMega644P
|
|
*
|
|
* +---\/---+
|
|
* (D 0) PB0 1| |40 PA0 (AI 0 / D31)
|
|
* (D 1) PB1 2| |39 PA1 (AI 1 / D30)
|
|
* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
|
|
* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
|
|
* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
|
|
* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
|
|
* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
|
|
* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
|
|
* RST 9| |32 AREF
|
|
* VCC 10| |31 GND
|
|
* GND 11| |30 AVCC
|
|
* XTAL2 12| |29 PC7 (D 23)
|
|
* XTAL1 13| |28 PC6 (D 22)
|
|
* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
|
|
* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
|
|
* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
|
|
* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
|
|
* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
|
|
* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
|
|
* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
|
|
* +--------+
|
|
*
|
|
****************************************************************************************
|
|
*
|
|
* ATMega644P (SMD)
|
|
*
|
|
* +--------+
|
|
* MOSI (D 5) PB5 1| O |44 PB4 (D 4) PWM
|
|
* MISO (D 6) PB6 2| |43 PB3 (D 3) PWM
|
|
* SCK (D 7) PB7 3| |42 PB2 (D 2) INT2
|
|
* RST 4| |41 PB1 (D 1)
|
|
* Vcc 5| |40 PB0 (D 0)
|
|
* GND 6| |39 GND
|
|
* XTAL2 7| |38 Vcc
|
|
* XTAL1 8| |37 PA0 (AI 0 / D31)
|
|
* RX0 (D 8) PD0 9| |36 PA1 (AI 1 / D30)
|
|
* TX0 (D 9) PD1 10| |35 PA2 (AI 2 / D29)
|
|
* INT0 RX1 (D 10) PD2 11| |34 PA3 (AI 3 / D28)
|
|
* + +
|
|
* INT1 TX1 (D 11) PD3 12| |33 PA4 (AI 4 / D27)
|
|
* PWM (D 12) PD4 13| |32 PA5 (AI 5 / D26)
|
|
* PWM (D 13) PD5 14| |31 PA6 (AI 6 / D25)
|
|
* PWM (D 14) PD6 15| |30 PA7 (AI 7 / D24)
|
|
* PWM (D 15) PD7 16| |29 AREF
|
|
* Vcc 17| |28 GND
|
|
* GND 18| |27 AVCC
|
|
* (D 16) PC0 19| |26 PC7 (D 23)
|
|
* (D 17) PC1 20| |25 PC6 (D 22)
|
|
* (D 18) PC2 21| |24 PC5 (D 21) TDI
|
|
* (D 19) PC3 22| |23 PC4 (D 20) TDO
|
|
* +--------+
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 1
|
|
#define KNOWN_BOARD 1
|
|
|
|
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN 19
|
|
#define X_MIN_PIN 20
|
|
#define X_MAX_PIN 21
|
|
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 19
|
|
#define Y_MIN_PIN 25
|
|
#define Y_MAX_PIN 26
|
|
|
|
#define Z_STEP_PIN 29
|
|
#define Z_DIR_PIN 30
|
|
#define Z_ENABLE_PIN 31
|
|
#define Z_MIN_PIN 2
|
|
#define Z_MAX_PIN 1
|
|
|
|
#define E_STEP_PIN 12
|
|
#define E_DIR_PIN 16
|
|
#define E_ENABLE_PIN 3
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS -1
|
|
#define LED_PIN 0
|
|
#define FAN_PIN -1
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#define HEATER_0_PIN 14
|
|
#define TEMP_0_PIN 4 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
|
|
|
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
/****************************************************************************************
|
|
* RepRap Motherboard ****---NOOOOOO RS485/EXTRUDER CONTROLLER!!!!!!!!!!!!!!!!!---*******
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 2
|
|
#define KNOWN_BOARD 1
|
|
|
|
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) && !defined(__ATmega644P__) && !defined(__ATmega1284P__)
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN 19
|
|
#define X_MIN_PIN 20
|
|
#define X_MAX_PIN 21
|
|
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 24
|
|
#define Y_MIN_PIN 25
|
|
#define Y_MAX_PIN 26
|
|
|
|
#define Z_STEP_PINN 27
|
|
#define Z_DIR_PINN 28
|
|
#define Z_ENABLE_PIN 29
|
|
#define Z_MIN_PIN 30
|
|
#define Z_MAX_PIN 31
|
|
|
|
#define E_STEP_PIN 17
|
|
#define E_DIR_PIN 16
|
|
#define E_ENABLE_PIN -1
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 4
|
|
#define LED_PIN 0
|
|
|
|
#define SD_CARD_WRITE 2
|
|
#define SD_CARD_DETECT 3
|
|
#define SD_CARD_SELECT 4
|
|
|
|
//our RS485 pins
|
|
#define TX_ENABLE_PIN 12
|
|
#define RX_ENABLE_PIN 13
|
|
|
|
//pin for controlling the PSU.
|
|
#define PS_ON_PIN 14
|
|
|
|
#define FAN_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#define HEATER_0_PIN -1
|
|
#define TEMP_0_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
/****************************************************************************************
|
|
* Gen3 PLUS for RepRap Motherboard V1.2
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 21
|
|
#define KNOWN_BOARD 1
|
|
|
|
#ifndef __AVR_ATmega644P__
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
|
|
//x axis pins
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN 19
|
|
#define X_MIN_PIN 20
|
|
#define X_MAX_PIN -1
|
|
|
|
//y axis pins
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 24
|
|
#define Y_MIN_PIN 25
|
|
#define Y_MAX_PIN -1
|
|
|
|
//z axis pins
|
|
#define Z_STEP_PIN 27
|
|
#define Z_DIR_PIN 28
|
|
#define Z_ENABLE_PIN 29
|
|
#define Z_MIN_PIN 30
|
|
#define Z_MAX_PIN -1
|
|
|
|
#define E_DIR_PIN 21
|
|
#define E_STEP_PIN 17
|
|
#define E_ENABLE_PIN 13
|
|
|
|
//heaters
|
|
|
|
//pin for hot end heater
|
|
#define HEATER_0_PIN 12
|
|
|
|
//Pin for heated bed heater
|
|
#define HEATER_1_PIN 16
|
|
|
|
|
|
//pin for debugging.
|
|
#define DEBUG_PIN -1
|
|
|
|
//SD card pin
|
|
|
|
#define SDSS 4
|
|
|
|
#define SDPOWER -1
|
|
#define FAN_PIN -1
|
|
#define TEMP_0_PIN 0
|
|
#define TEMP_1_PIN 5
|
|
#define LED_PIN -1
|
|
|
|
//pin for controlling the PSU.
|
|
#define PS_ON_PIN 14
|
|
|
|
#endif
|
|
|
|
/****************************************************************************************
|
|
* Gen3 Monolithic Electronics
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 22
|
|
#define KNOWN_BOARD 1
|
|
|
|
#ifndef __AVR_ATmega644P__
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#define DEBUG_PIN 0
|
|
|
|
|
|
// x axis
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 18
|
|
#define X_MIN_PIN 20
|
|
#define X_ENABLE_PIN 24 //actually uses Y_enable_pin
|
|
#define X_MAX_PIN -1
|
|
|
|
// y axes
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_MIN_PIN 25
|
|
#define Y_ENABLE_PIN 24 //shared with X_enable_pin
|
|
#define Y_MAX_PIN -1
|
|
|
|
// z axes
|
|
#define Z_STEP_PIN 27
|
|
#define Z_DIR_PIN 28
|
|
#define Z_MIN_PIN 30
|
|
#define Z_ENABLE_PIN 29
|
|
#define Z_MAX_PIN -1
|
|
|
|
//extruder pins
|
|
#define E_STEP_PIN 12
|
|
#define E_DIR_PIN 17
|
|
#define E_ENABLE_PIN 3
|
|
#define HEATER_0_PIN 16
|
|
#define TEMP_0_PIN 0
|
|
|
|
#define FAN_PIN -1
|
|
|
|
//bed pins
|
|
#define HEATER_1_PIN -1
|
|
#define TEMP_1_PIN -1
|
|
|
|
|
|
#define SDSS -1
|
|
#define SDPOWER -1
|
|
#define LED_PIN -1
|
|
|
|
//pin for controlling the PSU.
|
|
#define PS_ON_PIN 14
|
|
|
|
#endif
|
|
|
|
|
|
/****************************************************************************************
|
|
* Gen3 PLUS for TechZone Gen3 Remix Motherboard
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 23
|
|
#define KNOWN_BOARD 1
|
|
|
|
#ifndef __AVR_ATmega644P__
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
|
|
//x axis pins
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN 24 //same as E/Y_enable_pin
|
|
#define X_MIN_PIN 20
|
|
#define X_MAX_PIN -1
|
|
|
|
//y axis pins
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 24 //same as E/X_enable_pin
|
|
#define Y_MIN_PIN 25
|
|
#define Y_MAX_PIN -1
|
|
|
|
//z axis pins
|
|
#define Z_STEP_PIN 27
|
|
#define Z_DIR_PIN 28
|
|
#define Z_ENABLE_PIN 29
|
|
#define Z_MIN_PIN 30
|
|
#define Z_MAX_PIN -1
|
|
|
|
#define E_DIR_PIN 21
|
|
#define E_STEP_PIN 19
|
|
#define E_ENABLE_PIN 24 //same as X/Y_enable_pin
|
|
|
|
//heaters
|
|
|
|
//pin for hot end heater
|
|
#define HEATER_0_PIN 16
|
|
|
|
//Pin for heated bed heater
|
|
#define HEATER_1_PIN 17
|
|
|
|
|
|
//pin for debugging.
|
|
#define DEBUG_PIN -1
|
|
|
|
//SD card pin
|
|
|
|
#define SDSS 4
|
|
|
|
#define SDPOWER -1
|
|
#define FAN_PIN -1
|
|
#define TEMP_0_PIN 0
|
|
#define TEMP_1_PIN 5
|
|
#define LED_PIN -1
|
|
|
|
//pin for controlling the PSU.
|
|
#define PS_ON_PIN 14
|
|
|
|
#endif
|
|
|
|
|
|
/****************************************************************************************
|
|
* Arduino Mega pin assignment
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 33
|
|
#define MOTHERBOARD 3
|
|
#define RAMPS_V_1_3
|
|
#endif
|
|
#if MOTHERBOARD == 3
|
|
#define KNOWN_BOARD 1
|
|
|
|
//////////////////FIX THIS//////////////
|
|
#ifndef __AVR_ATmega1280__
|
|
#ifndef __AVR_ATmega2560__
|
|
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
#endif
|
|
|
|
// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1
|
|
// #define RAMPS_V_1_3
|
|
// #define RAMPS_V_1_0
|
|
|
|
#ifdef RAMPS_V_1_3
|
|
|
|
#define X_STEP_PIN 54
|
|
#define X_DIR_PIN 55
|
|
#define X_ENABLE_PIN 38
|
|
#define X_MIN_PIN 3
|
|
#define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable.
|
|
|
|
#define Y_STEP_PIN 60
|
|
#define Y_DIR_PIN 61
|
|
#define Y_ENABLE_PIN 56
|
|
#define Y_MIN_PIN 14
|
|
#define Y_MAX_PIN -1 //15
|
|
|
|
#define Z_STEP_PIN 46
|
|
#define Z_DIR_PIN 48
|
|
#define Z_ENABLE_PIN 62
|
|
#define Z_MIN_PIN 18
|
|
#define Z_MAX_PIN -1 //19
|
|
|
|
#define E_STEP_PIN 26
|
|
#define E_DIR_PIN 28
|
|
#define E_ENABLE_PIN 24
|
|
|
|
#define E_1_STEP_PIN 36
|
|
#define E_1_DIR_PIN 34
|
|
#define E_1_ENABLE_PIN 30
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 53
|
|
#define LED_PIN 13
|
|
#define FAN_PIN 9
|
|
#define PS_ON_PIN 12
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#define HEATER_0_PIN 10
|
|
#define HEATER_1_PIN 8
|
|
#define TEMP_0_PIN 13 // ANALOG NUMBERING
|
|
#define TEMP_1_PIN 14 // ANALOG NUMBERING
|
|
#define TEMP_2_PIN 15 // ANALOG NUMBERING
|
|
|
|
#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default
|
|
|
|
#define X_STEP_PIN 26
|
|
#define X_DIR_PIN 28
|
|
#define X_ENABLE_PIN 24
|
|
#define X_MIN_PIN 3
|
|
#define X_MAX_PIN -1 //2
|
|
|
|
#define Y_STEP_PIN 38
|
|
#define Y_DIR_PIN 40
|
|
#define Y_ENABLE_PIN 36
|
|
#define Y_MIN_PIN 16
|
|
#define Y_MAX_PIN -1 //17
|
|
|
|
#define Z_STEP_PIN 44
|
|
#define Z_DIR_PIN 46
|
|
#define Z_ENABLE_PIN 42
|
|
#define Z_MIN_PIN 18
|
|
#define Z_MAX_PIN -1 //19
|
|
|
|
#define E_STEP_PIN 32
|
|
#define E_DIR_PIN 34
|
|
#define E_ENABLE_PIN 30
|
|
|
|
#define SDPOWER 48
|
|
#define SDSS 53
|
|
#define LED_PIN 13
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
|
|
#ifdef RAMPS_V_1_0 // RAMPS_V_1_0
|
|
#define HEATER_0_PIN 12 // RAMPS 1.0
|
|
#define HEATER_1_PIN -1 // RAMPS 1.0
|
|
#define FAN_PIN 11 // RAMPS 1.0
|
|
|
|
#else // RAMPS_V_1_1 or RAMPS_V_1_2
|
|
#define HEATER_0_PIN 10 // RAMPS 1.1
|
|
#define HEATER_1_PIN 8 // RAMPS 1.1
|
|
#define FAN_PIN 9 // RAMPS 1.1
|
|
#endif
|
|
|
|
#define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
|
#define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
|
#endif
|
|
|
|
// SPI for Max6675 Thermocouple
|
|
|
|
#ifndef SDSUPPORT
|
|
// these pins are defined in the SD library if building with SD support
|
|
#define SCK_PIN 52
|
|
#define MISO_PIN 50
|
|
#define MOSI_PIN 51
|
|
#define MAX6675_SS 53
|
|
#else
|
|
#define MAX6675_SS 49
|
|
#endif
|
|
|
|
|
|
#endif
|
|
/****************************************************************************************
|
|
* Duemilanove w/ ATMega328P pin assignment
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 4
|
|
#define KNOWN_BOARD 1
|
|
|
|
#ifndef __AVR_ATmega328P__
|
|
#error Oops! Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#define X_STEP_PIN 19
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN -1
|
|
#define X_MIN_PIN 17
|
|
#define X_MAX_PIN -1
|
|
|
|
#define Y_STEP_PIN 10
|
|
#define Y_DIR_PIN 7
|
|
#define Y_ENABLE_PIN -1
|
|
#define Y_MIN_PIN 8
|
|
#define Y_MAX_PIN -1
|
|
|
|
#define Z_STEP_PIN 13
|
|
#define Z_DIR_PIN 3
|
|
#define Z_ENABLE_PIN 2
|
|
#define Z_MIN_PIN 4
|
|
#define Z_MAX_PIN -1
|
|
|
|
#define E_STEP_PIN 11
|
|
#define E_DIR_PIN 12
|
|
#define E_ENABLE_PIN -1
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS -1
|
|
#define LED_PIN -1
|
|
#define FAN_PIN 5
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#define HEATER_0_PIN 6
|
|
#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
|
|
|
|
|
#endif
|
|
|
|
/****************************************************************************************
|
|
* Gen6 pin assignment
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 51
|
|
#define MOTHERBOARD 5
|
|
#define GEN6_DELUXE
|
|
#endif
|
|
|
|
#if MOTHERBOARD == 5
|
|
#define KNOWN_BOARD 1
|
|
|
|
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
//x axis pins
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN 19
|
|
#define X_MIN_PIN 20
|
|
#define X_MAX_PIN -1
|
|
|
|
//y axis pins
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 24
|
|
#define Y_MIN_PIN 25
|
|
#define Y_MAX_PIN -1
|
|
|
|
//z axis pins
|
|
#define Z_STEP_PIN 27
|
|
#define Z_DIR_PIN 28
|
|
#define Z_ENABLE_PIN 29
|
|
#define Z_MIN_PIN 30
|
|
#define Z_MAX_PIN -1
|
|
|
|
//extruder pins
|
|
#define E_STEP_PIN 4 //Edited @ EJE Electronics 20100715
|
|
#define E_DIR_PIN 2 //Edited @ EJE Electronics 20100715
|
|
#define E_ENABLE_PIN 3 //Added @ EJE Electronics 20100715
|
|
#define TEMP_0_PIN 5 //changed @ rkoeppl 20110410
|
|
#define HEATER_0_PIN 14 //changed @ rkoeppl 20110410
|
|
|
|
#ifdef GEN6_DELUXE
|
|
#define HEATER_1_PIN 1
|
|
#define TEMP_1_PIN 0
|
|
#else
|
|
#define HEATER_1_PIN -1
|
|
#define TEMP_1_PIN -1
|
|
#endif
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 17
|
|
#define LED_PIN -1 //changed @ rkoeppl 20110410
|
|
#define FAN_PIN -1 //changed @ rkoeppl 20110410
|
|
#define PS_ON_PIN -1 //changed @ rkoeppl 20110410
|
|
//our pin for debugging.
|
|
|
|
#define DEBUG_PIN 0
|
|
|
|
//our RS485 pins
|
|
#define TX_ENABLE_PIN 12
|
|
#define RX_ENABLE_PIN 13
|
|
|
|
#endif
|
|
/****************************************************************************************
|
|
* Sanguinololu pin assignment
|
|
*
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 62
|
|
#define MOTHERBOARD 6
|
|
#define SANGUINOLOLU_V_1_2
|
|
#endif
|
|
#if MOTHERBOARD == 6
|
|
#define KNOWN_BOARD 1
|
|
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
#define X_STEP_PIN 15
|
|
#define X_DIR_PIN 21
|
|
#define X_MIN_PIN 18
|
|
#define X_MAX_PIN -2
|
|
|
|
#define Y_STEP_PIN 22
|
|
#define Y_DIR_PIN 23
|
|
#define Y_MIN_PIN 19
|
|
#define Y_MAX_PIN -1
|
|
|
|
#define Z_STEP_PIN 3
|
|
#define Z_DIR_PIN 2
|
|
#define Z_MIN_PIN 20
|
|
#define Z_MAX_PIN -1
|
|
|
|
#define E_STEP_PIN 1
|
|
#define E_DIR_PIN 0
|
|
|
|
#define LED_PIN -1
|
|
|
|
#define FAN_PIN -1
|
|
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#define HEATER_0_PIN 13 // (extruder)
|
|
|
|
#ifdef SANGUINOLOLU_V_1_2
|
|
|
|
#define HEATER_1_PIN 12 // (bed)
|
|
#define X_ENABLE_PIN 14
|
|
#define Y_ENABLE_PIN 14
|
|
#define Z_ENABLE_PIN 26
|
|
#define E_ENABLE_PIN 14
|
|
#else
|
|
|
|
#define HEATER_1_PIN 14 // (bed)
|
|
#define X_ENABLE_PIN -1
|
|
#define Y_ENABLE_PIN -1
|
|
#define Z_ENABLE_PIN -1
|
|
#define E_ENABLE_PIN -1
|
|
|
|
#endif
|
|
|
|
#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
|
|
#define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
|
|
#define SDPOWER -1
|
|
#define SDSS 31
|
|
|
|
#endif
|
|
|
|
/****************************************************************************************
|
|
* Gen7 pin assignment
|
|
*
|
|
****************************************************************************************
|
|
* for Gen7 to work properly, you should reset your fuses to lfuse= 0xF7 ; hfuse = 0xD4 ; efuse = FD;
|
|
* else you will always get a "brown out reset" loop resetting the firmware
|
|
* you need a programmer to set the fuses
|
|
**/
|
|
#if MOTHERBOARD == 71 //GEN7 with 20 Mhz
|
|
#define MOTHERBOARD 7
|
|
#define QUARZ_20MHZ
|
|
#endif
|
|
|
|
#if MOTHERBOARD == 7
|
|
#define KNOWN_BOARD 1
|
|
|
|
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) && !defined(__AVR_ATmega644__)
|
|
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
|
|
#endif
|
|
|
|
//x axis pins
|
|
#define X_STEP_PIN 19
|
|
#define X_DIR_PIN 18
|
|
#define X_ENABLE_PIN 24
|
|
#define X_MIN_PIN 7
|
|
#define X_MAX_PIN -1 //X - Maxpin is 6
|
|
|
|
//y axis pins
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 24
|
|
#define Y_MIN_PIN 5
|
|
#define Y_MAX_PIN -1 //Y - Maxpin is 2
|
|
|
|
//z axis pins
|
|
#define Z_STEP_PIN 26
|
|
#define Z_DIR_PIN 25
|
|
#define Z_ENABLE_PIN 24
|
|
#define Z_MIN_PIN 1
|
|
#define Z_MAX_PIN -1 //Z - Maxpin is 0
|
|
|
|
//extruder pins
|
|
#define E_STEP_PIN 28
|
|
#define E_DIR_PIN 27
|
|
#define E_ENABLE_PIN 24
|
|
#define TEMP_0_PIN 1 // Extruder
|
|
#define HEATER_0_PIN 4 // Extruder
|
|
#define HEATER_1_PIN 3 // Bed
|
|
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS -1
|
|
#define LED_PIN -1
|
|
#define TEMP_1_PIN 2 //Bed
|
|
#define FAN_PIN -1
|
|
#define PS_ON_PIN 15
|
|
|
|
#endif
|
|
|
|
/****************************************************************************************
|
|
* Teensylu 0.7 pin assingments (ATMEGA90USB)
|
|
* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE!
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 8
|
|
#define MOTHERBOARD 8
|
|
#define KNOWN_BOARD 1
|
|
|
|
|
|
#define X_STEP_PIN 28
|
|
#define X_DIR_PIN 29
|
|
#define X_ENABLE_PIN 19
|
|
#define X_MIN_PIN 25
|
|
#define X_MAX_PIN -1
|
|
|
|
#define Y_STEP_PIN 30
|
|
#define Y_DIR_PIN 31
|
|
#define Y_ENABLE_PIN 26
|
|
#define Y_MIN_PIN 20
|
|
#define Y_MAX_PIN -1
|
|
|
|
#define Z_STEP_PIN 32
|
|
#define Z_DIR_PIN 33
|
|
#define Z_ENABLE_PIN 17
|
|
#define Z_MIN_PIN 27
|
|
#define Z_MAX_PIN -1
|
|
|
|
#define E_STEP_PIN 34
|
|
#define E_DIR_PIN 35
|
|
#define E_ENABLE_PIN 13
|
|
|
|
#define HEATER_0_PIN 15 // Extruder
|
|
#define HEATER_1_PIN 14 // Bed
|
|
#define FAN_PIN 16 // Fan
|
|
|
|
#define TEMP_0_PIN 7 // Extruder
|
|
#define TEMP_1_PIN 6 // Bed
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 20
|
|
#define LED_PIN -1
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
#define ALARM_PIN -1
|
|
|
|
#ifndef SDSUPPORT
|
|
// these pins are defined in the SD library if building with SD support
|
|
#define SCK_PIN 21
|
|
#define MISO_PIN 22
|
|
#define MOSI_PIN 23
|
|
#endif
|
|
|
|
#endif
|
|
|
|
/****************************************************************************************
|
|
* Printrboard Rev. B pin assingments (ATMEGA90USB1286)
|
|
* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE!
|
|
* See http://reprap.org/wiki/Printrboard for more info
|
|
****************************************************************************************/
|
|
#if MOTHERBOARD == 9
|
|
#define MOTHERBOARD 9
|
|
#define KNOWN_BOARD 1
|
|
|
|
|
|
#define X_STEP_PIN 28
|
|
#define X_DIR_PIN 29
|
|
#define X_ENABLE_PIN 19
|
|
#define X_MIN_PIN 47
|
|
#define X_MAX_PIN -1
|
|
|
|
#define Y_STEP_PIN 30
|
|
#define Y_DIR_PIN 31
|
|
#define Y_ENABLE_PIN 18
|
|
#define Y_MIN_PIN 20
|
|
#define Y_MAX_PIN -1
|
|
|
|
#define Z_STEP_PIN 32
|
|
#define Z_DIR_PIN 33
|
|
#define Z_ENABLE_PIN 17
|
|
#define Z_MIN_PIN 36
|
|
#define Z_MAX_PIN -1
|
|
|
|
#define E_STEP_PIN 34
|
|
#define E_DIR_PIN 35
|
|
#define E_ENABLE_PIN 13
|
|
|
|
#define HEATER_0_PIN 15 // Extruder
|
|
#define HEATER_1_PIN 14 // Bed
|
|
#define FAN_PIN 16 // Fan
|
|
|
|
#define TEMP_0_PIN 1 // Extruder
|
|
#define TEMP_1_PIN 0 // Bed
|
|
|
|
#define SDPOWER -1
|
|
#define SDSS 2
|
|
#define LED_PIN -1
|
|
#define PS_ON_PIN -1
|
|
#define KILL_PIN -1
|
|
|
|
#ifndef SDSUPPORT
|
|
// these pins are defined in the SD library if building with SD support
|
|
#define SCK_PIN 21
|
|
#define MISO_PIN 22
|
|
#define MOSI_PIN 23
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#ifndef KNOWN_BOARD
|
|
#error Unknown MOTHERBOARD value in configuration.h
|
|
#endif
|
|
|
|
|
|
//List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
|
|
const int sensitive_pins[] = {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, E_STEP_PIN, E_DIR_PIN, E_ENABLE_PIN, LED_PIN, PS_ON_PIN, HEATER_0_PIN, HEATER_1_PIN, FAN_PIN, TEMP_0_PIN+55, TEMP_1_PIN+55, TEMP_2_PIN+55, TEMP_BED_PIN+55};
|
|
|
|
#endif
|
|
|
|
|