3a29ee97d1
- M206 - set additional homeing offset (Thank to se5a for this idea) (First Version is without saving to EEPROM) - Option for minimum FAN start speed --> #define MINIMUM_FAN_START_SPEED 50 (set it to zero to deaktivate)
138 lines
4.6 KiB
C
138 lines
4.6 KiB
C
// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
|
|
// Licence: GPL
|
|
|
|
//Check Version of Arduino and then include the right libraries
|
|
#if defined(ARDUINO) && ARDUINO >= 100
|
|
#include "Arduino.h"
|
|
#else
|
|
#include <WProgram.h>
|
|
#endif
|
|
|
|
#include "fastio.h"
|
|
|
|
extern "C" void __cxa_pure_virtual();
|
|
|
|
#define FORCE_INLINE __attribute__((always_inline)) inline
|
|
|
|
#if X_ENABLE_PIN > -1
|
|
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
|
|
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
|
|
#else
|
|
#define enable_x() ;
|
|
#define disable_x() ;
|
|
#endif
|
|
#if Y_ENABLE_PIN > -1
|
|
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
|
|
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
|
|
#else
|
|
#define enable_y() ;
|
|
#define disable_y() ;
|
|
#endif
|
|
#if Z_ENABLE_PIN > -1
|
|
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
|
|
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
|
|
#else
|
|
#define enable_z() ;
|
|
#define disable_z() ;
|
|
#endif
|
|
#if E_ENABLE_PIN > -1
|
|
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
|
|
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
|
|
#else
|
|
#define enable_e() ;
|
|
#define disable_e() ;
|
|
#endif
|
|
|
|
#define X_AXIS 0
|
|
#define Y_AXIS 1
|
|
#define Z_AXIS 2
|
|
#define E_AXIS 3
|
|
|
|
|
|
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
|
|
// the source g-code and may never actually be reached if acceleration management is active.
|
|
typedef struct {
|
|
// Fields used by the bresenham algorithm for tracing the line
|
|
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
|
|
|
|
unsigned long step_event_count; // The number of step events required to complete this block
|
|
long accelerate_until; // The index of the step event on which to stop acceleration
|
|
long decelerate_after; // The index of the step event on which to start decelerating
|
|
long acceleration_rate; // The acceleration rate used for acceleration calculation
|
|
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
|
|
|
|
#ifdef ADVANCE
|
|
long advance_rate;
|
|
volatile long initial_advance;
|
|
volatile long final_advance;
|
|
float advance;
|
|
#endif
|
|
|
|
// Fields used by the motion planner to manage acceleration
|
|
// float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
|
|
float nominal_speed; // The nominal speed for this block in mm/min
|
|
float entry_speed; // Entry speed at previous-current junction in mm/min
|
|
float max_entry_speed; // Maximum allowable junction entry speed in mm/min
|
|
float millimeters; // The total travel of this block in mm
|
|
float acceleration; // acceleration mm/sec^2
|
|
unsigned char recalculate_flag; // Planner flag to recalculate trapezoids on entry junction
|
|
unsigned char nominal_length_flag; // Planner flag for nominal speed always reached
|
|
|
|
|
|
// Settings for the trapezoid generator
|
|
long nominal_rate; // The nominal step rate for this block in step_events/sec
|
|
long initial_rate; // The jerk-adjusted step rate at start of block
|
|
long final_rate; // The minimal rate at exit
|
|
long acceleration_st; // acceleration steps/sec^2
|
|
volatile char busy;
|
|
} block_t;
|
|
|
|
|
|
void FlushSerialRequestResend();
|
|
void ClearToSend();
|
|
|
|
void analogWrite_check(uint8_t check_pin, int val);
|
|
void showString (PGM_P s);
|
|
|
|
void manage_inactivity(byte debug);
|
|
|
|
void get_command();
|
|
void get_coordinates();
|
|
void prepare_move();
|
|
void prepare_arc_move(char isclockwise);
|
|
FORCE_INLINE void process_commands();
|
|
#ifdef USE_ARC_FUNCTION
|
|
FORCE_INLINE void get_arc_coordinates();
|
|
#endif
|
|
|
|
void kill(byte debug);
|
|
|
|
void check_axes_activity();
|
|
void plan_init();
|
|
void st_init();
|
|
void tp_init();
|
|
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
|
|
void plan_set_position(float x, float y, float z, float e);
|
|
void st_wake_up();
|
|
void st_synchronize();
|
|
void st_set_position(const long &x, const long &y, const long &z, const long &e);
|
|
|
|
void check_buffer_while_arc();
|
|
|
|
#ifdef SDSUPPORT
|
|
void print_disk_info(void);
|
|
#endif //SDSUPPORT
|
|
|
|
#if (MINIMUM_FAN_START_SPEED > 0)
|
|
void manage_fan_start_speed(void);
|
|
#endif
|
|
|
|
#ifdef DEBUG
|
|
void log_message(char* message);
|
|
void log_bool(char* message, bool value);
|
|
void log_int(char* message, int value);
|
|
void log_long(char* message, long value);
|
|
void log_float(char* message, float value);
|
|
void log_uint(char* message, unsigned int value);
|
|
void log_ulong(char* message, unsigned long value);
|
|
#endif
|